White - UPVC Shiplap Cladding 45mm Drip Trim

Product Information

Cut your cladding trim with your desired cutting tool, be sure to fully support the trim while cutting. Once you have removed the supporting layer, the face profile of the trim can simply be adhered to the corner or edge, using either silicone or mitre adhesive. Beginning to fit your trims A utility knife can be used to easily score the trims so that they simply snap along the score line. Important tips

For example if you’re fitting a trim over a 2m join, using a trim that measures 2.7m, you aren’t going to be able to utilise the 0.7m off cut effectively without having a joint with another cutting of trim. From bright and shiny chrome effect to the neutral smooth looking matte effect trims, there are a variety of designs to suit your needs. Measuring for trims Primarily, roof edging, also known as drip edge, provides superior protection against water damage by preventing water from seeping into vulnerable areas along the roof's edge, thus extending the lifespan of your roof and reducing the risk of leaks. Additionally, roof edging aids in directing rainwater away from your home's foundation, mitigating potential structural issues. Furthermore, roof edging contributes to improved energy efficiency by creating a barrier against drafts and heat loss. Incorporating roof edging not only safeguards your roof but also adds a polished look to your home's exterior. Below are the most important points to consider when taking your measurements: Do you require a mitred corner or edge to allow for trimming corners? A half-clad room, bath panel, or where your cladding would meet a skirting could use an end cap to finish off the edge.

The most efficient way to mitre a joint is by hand with a utility blade and a measuring square. Although this is not suitable for coving as you will not be able to cut an accurate curve to meet another coving trim.

You're able to select a preferreddelivery date in your shopping basket. Whilst we aim to deliver your items on this date, it is not guaranteed. Trims are an excellent way to finish any unsightly gaps or edges that are left after or during the fitting process.This is to be mounted on the bottom of the installation - before the boards have been fitted - to provide a weather drip to angle any water away from the mounting wall. This can be used with either the 100mm V Joint or the 150mm Shiplap. cause staining of the profiles. Painting is not recommended on foam profiles unless done by an approved contractor. The Eurocell Building Plastics products supplied by Eurocell Profiles Ltd are produced in accordance with a BS EN 1SO There’s no bending and twisting the panels into place around previously fitted trims so it gives you a lot more freedom whilst installing.

It is fine to use this method for cutting L angle trims and end caps however. Avoid joins in your trims You must be careful and take your time while cutting to ensure you don’t damage the profile of the trim. With some cladding trims it may be easier to fit afterwards, such as external corners and coving trims. How to fit cladding trims after you have fitted your cladding

Ventilation gaps within the Closure Trims, paired with the 50mm space between the battens and boards, work together to ensure your building has adequate airflow to prevent moisture from building up. We recommend taking this into account when calculating your wastage. Ensuring you aren’t short on trims when it comes to fitting.

Fitting certain cladding trims first will give you a guideline and support when installing your cladding panels. Fitting trims to corners or wall to ceiling joins look great if they’re in one piece. One continuous trim always looks better, rather than many offcuts used together to cover one join. This is usually avoidable. We can only provide a delivery date and are not able to confirm the time delivery will be attempted. Therefore, we ask that somebody is able to accept and sign for your items throughout the started delivery date. Inserting cladding into a corner cladding trim will hold your panel into the corner while you fix it to the surface.Theres no need to worry about cutting your edges perfect as the internal trim will cover up all of the rough edges. To measure for trims correctly you must allow for a small excess. This will account for any mitred edges you may need to cut.Please note: it is recommended to leave a gap of 10mm between the Perforated Closure and the base of your in stallation, to ensure a necessary gap for airflow. The Perforated Closure needs to be perfectly level before fixing to the wall, as a Start Profile Trim will be fixed to the Perforated Closure. If your Perforated Closure is not fitted parallel, you may be at risk of unlevel cladding.