DCT Concealed Cabinet Door Hinge 35mm Template Jig Kit – European Hidden Hinge Boring Hole Cutter & Bit for Installation

Product Information

There are removable corner inserts, so the Ryobi jig can be used for round- or square-cornered hinges (though the latter will still need finishing manually with a chisel). A high-quality router bit is included, as is a self-centering drill bit for making the actual hinge holes. Both bits are conveniently stored onboard the jig body. Once adjusted suitably to allow the door to open and close without touching or binding on any surrounding surfaces you’re pretty much done, good job! Another important point to be aware of when hanging cupboard doors using concealed hinges is; how many hinges should you use? The answer to this is that it depends on the size and weight of the door itself. The Everbilt jig is basically an L-shaped piece of transparent plastic that is held against the door edge. Holes allow pencil marks to be made for the hinge and retaining screws. The jig is then put aside and the relevant holes drilled. Any adjustment for offset will need to be done manually, which could lead to errors creeping in.

Hinge and Mounting Plate Jig - Cup Sizes 26/35mm

Durability is assured by the cast-aluminum construction. For transportation, the jig is dismantled into two pieces, and it comes with a carrying case. A guide bush for the router cutter is included, though the cutter itself is not—rather disappointing given the Trend door hinge jig’s high price. If the cup recess is set at the standard 22mm or so in from the edge of the door the mounting plate will need to be raised around 8mm off of the inner side of the unit. A thin 8mm piece of door stop is ideal for this. Better quality hinges are generally stronger and hold their shape much longer than their cheaper counterparts. If you’re using the IKEA Ultrusta cabinet hinge from the new Sektion system, here are a few measurements you’ll need to fashion your template. Drill the hole in the door with a 35mm hinge cutter for your drill or router. It is easy to be critical, but for a one-off job, or for someone who has a pillar drill to set depth, the Everbilt does the job at a fraction of the price of most competitors.

Different Types of Concealed Hinge and how They are Measured

Fitting a concealed cabinet hinge is a slightly different process to fitting a standard hinge in that it needs to fitted slightly offset from the edge of the door and front edge of the cabinet carcass, so accurate measuring and marking is a must if the cabinet door is to fit correctly. This will ensure the sits totally square once closed. Tools and Materials Needed for Fitting Concealed Hinges

Template for Ø35mm and 26mm Hinge LOOTICH Hole Drilling Jig Template for Ø35mm and 26mm Hinge

Hinge cup: The hinge cup is the part of a concealed hing that is fixed to the cabinet door. A 10-12mm recess is cut into the rear of the door for the cup to sit in Buying a door jig is the easy option, but with care, it is possible to make your own. In fact, for cabinet doors, a jig isn’t strictly necessary. If you can measure and mark accurately, hold the drill vertically, and judge the depth of a hole, then a Forstner bit of the appropriate diameter to match the hinge is all that is required. Owners of pillar drills will find the task easier, but a portable drill and a steady hand can get the job done. Even skilled carpenters usually turn to a door hinge jig to ensure the fast, accurate positioning of door hardware. This tool helps obtain the precise measurements required for the task of installing doors. Most are simple enough to be used by even relatively inexperienced DIYers, and most are very affordable—especially when compared to the cost of ruining a door. Repeat the same for the bottom and also for any other hinges, again remembering to measure from the correct point. Before explaining exactly how to measure and fit a concealed cabinet hinge to a kitchen or bathroom cupboard it’s important to fully understand each different part of the hinge and what it’s called so that when we refer to a particular part you’ll know exactly what we mean:If you need to use more hinges divide the space between the top and bottom marks equally depending on how many hinges you are adding e.g. if you are using 5 hinges, divide the space by 3 for your further 3 hinges. A router bit is required with full-size door hinge jigs, and one is often included. Shank size will be either ¼ inch or ½ inch. Neither is better than the other, but the size will determine the kind of router used. Some ½-inch routers include a ¼-inch collet as an option, whereas ¼-inch routers cannot use ½-inch bits. Once positioned accurately mark screw holes, drill a pilot hole and screw it in place. Repeat for any remaining hinges. Fit Cabinet Door to Unit or Framework Once the mounting plates are fixed you can then fit the door in place. Open out the hinge on the door so it is horizontally level with the door. As mentioned there are a few other sizes of concealed hinge including 40mm, but these tend to be for more heavy weight specialist applications. How Many Concealed Hinges Should you use on Each Door?

Paper Template for Blum Hinge - FineWoodworking Paper Template for Blum Hinge - FineWoodworking

This type of door hinge jig creates a round-cornered cutaway in the door edge, and suitable round-cornered hinges are widely available. However, door hinges were traditionally square, and when refitting a door to an existing frame, it will often be necessary to cut away the rounded area. This can be done with an ordinary woodworking chisel, but corner chisels specifically for the purpose are available. The next task is to measure and mark the positions using a pencil of each mounting plate on the inside of the cupboard or unit you are fixing your door to. If the door you have just fitted is a finished door e.g. doesn’t need painting, the final job to do is to now rub off any remaining pencil marks using a rubber. If it’s being painted don’t worry, the paint will hide any remaining marks. Cabinet door hinge jigs are simply held to the inside of the door using any convenient woodworking clamps. Ratcheting types are convenient because they are easy to use one-handed. Two clamps should be employed, one either side of the cutter guide, to ensure that the jig can’t twist.The above is a guide based on using standard 35mm euro concealed hinges, the type that are used on pretty much all kitchen cabinets and units. Firstly, measure and mark the same distance down from the top of the inside of your cabinet that you previously marked on the door for the top hinge, normally this is around 85-100mm. To successfully fit a concealed hinge to a cabinet and door you will need the following tools and materials: As you should now know what type of door you have and what type of concealed hinge to use it’s now time to get them fitted. Measure and Mark Hinge Cup Positions on Cabinet Door